View MIC3975-1_240181.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC3975
Micrel
MIC3975
750mA Cap Low-Voltage Low-Dropout Regulator
Final Information
General Description
The MIC3975 is a 750mA low-dropout linear voltage regulators that provide low-voltage, high-current output from an extremely small package. Utilizing Micrel's proprietary Super eta PNPTM pass element, the MIC3975 offers extremely low dropout (typically 300mV at 750mA) and low ground current (typically 6.5mA at 750mA). The MIC3975 is ideal for PC add-in cards that need to convert from standard 5V to 3.3V or 3.0V, 3.3V to 2.5V or 2.5V to 1.8V or 1.65V. A guaranteed maximum dropout voltage of 500mV over all operating conditions allows the MIC3975 to provide 2.5V from a supply as low as 3.0V and 1.8V or 1.65V from a supply as low as 2.25V. The MIC3975 is fully protected with overcurrent limiting, thermal shutdown, and reversed-battery protection. Fixed voltages of 5.0V, 3.3V, 3.0, 2.5V, 1.8V, and 1.65V are available. An adjustable output voltage option is available for voltages down to 1.24V.
Features
* Fixed and adjustable output voltages to 1.24V * 300mV typical dropout at 750mA Ideal for 3.0V to 2.5V conversion Ideal for 2.5V to 1.8V or 1.65V conversion * Stable with ceramic capacitor * 750mA minimum guaranteed output current * 1% initial accuracy * Low ground current * Current limiting and thermal shutdown * Reversed-battery protection * Reversed-leakage protection * Fast transient response * Low-profile MSOP-8
Applications
* * * * * * * * Fiber optic modules LDO linear regulator for PC add-in cards PowerPCTM power supplies High-efficiency linear power supplies SMPS post regulator Multimedia and PC processor supplies Battery chargers Low-voltage microcontrollers and digital logic
For other voltages, contact Micrel.
Ordering Information
Part Number MIC3975-1.65BMM MIC3975-1.8BMM MIC3975-2.5BMM MIC3975-3.0BMM MIC3975-3.3BMM MIC3975-5.0BMM MIC3975BMM Voltage 1.65V 1.8V 2.5V 3.0V 3.3V 5.0V Adj. Junction Temp. Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Package MSOP-8 MSOP-8 MSOP-8 MSOP-8 MSOP-8 MSOP-8 MSOP-8
Typical Applications
100k VIN 3.3V
ENABLE SHUTDOWN
MIC3975-2.5BMM IN OUT R1 EN FLG GND
Error Flag Output 2.5V 10F ceramic VIN 2.5V
ENABLE SHUTDOWN
MIC3975BMM IN OUT R1 EN ADJ GND R2
1.5V 10F ceramic
2.5V/750mA Regulator with Error Flag
Super eta PNP is a trademark of Micrel, Inc.
1.5V/750mA Adjustable Regulator
Micrel, Inc. * 1849 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 944-0970 * http://www.micrel.com
February 2003
1
MIC3975
MIC3975
Micrel
Pin Configuration
EN 1 IN 2 FLG 3 OUT 4 8 GND 7 GND 6 GND 5 GND EN 1 IN 2 ADJ 3 OUT 4 8 GND 7 GND 6 GND 5 GND
MIC3975-x.x Fixed MSOP-8 (MM)
Adjustable MSOP-8 (MM)
Pin Description
Pin No. Fixed 1 2 3 3 4 5-8 4 5-8 Pin No. Adjustable 1 2 EN IN FLG ADJ OUT GND Enable (Input): CMOS-compatible control input. Logic high = enable, logic low or open = shutdown. Supply (Input) Flag (Output): Open-collector error flag output. Active low = output undervoltage. Adjustment Input: Feedback input. Connect to resistive voltage-divider network. Regulator Output Ground Pin Name Pin Function
MIC3975
2
February 2003
MIC3975
Micrel
Absolute Maximum Ratings (Note 1)
Supply Voltage (VIN) ..................................... -20V to +20V Enable Voltage (VEN) .................................................. +20V Storage Temperature (TS) ....................... -65C to +150C Lead Temperature (soldering, 5 sec.) ....................... 260C ESD, Note 3
Operating Ratings (Note 2)
Supply Voltage (VIN) .................................. +2.25V to +16V Enable Voltage (VEN) .................................................. +16V Maximum Power Dissipation (PD(max)) .................... Note 4 Junction Temperature (TJ) ....................... -40C to +125C Package Thermal Resistance MSOP-8 (JA) ...................................................... 80C/W
Electrical Characteristics(Note 12)
VIN = VOUT + 1V; VEN = 2.25V; TJ = 25C, bold values indicate -40C TJ +125C; unless noted Symbol VOUT Parameter Output Voltage Line Regulation Load Regulation VOUT/T VDO Output Voltage Temp. Coefficient, Note 5 Dropout Voltage, Note 6 IOUT = 100mA, VOUT = -1% IOUT = 500mA, VOUT = -1% IOUT = 750mA, VOUT = -1% IGND Ground Current, Note 7 IOUT = 100mA, VIN = VOUT + 1V IOUT = 500mA, VIN = VOUT + 1V IOUT = 750mA, VIN = VOUT + 1V IOUT(lim) Enable Input VEN IEN Enable Input Voltage logic low (off) logic high (on) Enable Input Current VEN = 2.25V VEN = 0.8V Flag Output IFLG(leak) VFLG(do) VFLG Output Leakage Current Output Low Voltage Low Threshold High Threshold Hysteresis VOH = 16V VIN = 2.250V, IOL, = 250A, Note 9 % of VOUT % of VOUT 1 93 99.2 0.01 210 1 2 300 400 A A mV mV % % % 2.25 1 15 30 75 2 4 0.8 V V A A A A Current Limit VOUT = 0V, VIN = VOUT + 1V Condition 10mA 10mA IOUT 750mA, VOUT + 1V VIN 8V IOUT = 10mA, VOUT + 1V VIN 16V VIN = VOUT + 1V, 10mA IOUT 750mA, Min -1 -2 0.06 0.2 40 140 225 300 400 4 7.5 1.8 15 2.5 500 Typ Max 1 2 0.5 1 100 200 250 Units % % % % ppm/C mV mV mV mV A mA mA A
February 2003
3
MIC3975
MIC3975
Symbol Parameter Condition Min Typ Max
Micrel
Units
Adjustable Output Only Reference Voltage Note 10 Adjust Pin Bias Current Reference Voltage Temp. Coefficient Adjust Pin Bias Current Temp. Coefficient
Note 1. Note 2. Note 3. Note 4. Note 5. Note 6. Note 7. Note 8. Note 9. Exceeding the absolute maximum ratings may damage the device. The device is not guaranteed to function outside its operating rating. Devices are ESD sensitive. Handling precautions recommended. PD(max) = (TJ(max) - TA) / JA, where JA depends upon the printed circuit layout. See "Applications Information." Output voltage temperature coefficient is VOUT(worst case) / (TJ(max) - TJ(min)) where TJ(max) is +125C and TJ(min) is -40C. VDO = VIN - VOUT when VOUT decreases to 98% of its nominal output voltage with VIN = VOUT + 1V. For output voltages below 2.25V, dropout voltage is the input-to-output voltage differential with the minimum input voltage being 2.25V. Minimum input operating voltage is 2.25V. IGND is the quiescent current. IIN = IGND + IOUT. VEN 0.8V, VIN 8V, and VOUT = 0V. For a 2.5V device, VIN = 2.250V (device is in dropout).
1.228 1.215 1.203
1.240
1.252 1.265 1.277 80 120
V V V nA nA ppm/C nA/C
40 Note 11 20 0.1
Note 10. VREF VOUT (VIN - 1V), 2.25V VIN 16V, 10mA IL 750mA, TJ = TMAX. Note 11. Thermal regulation is defined as the change in output voltage at a time t after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 200mA load pulse at VIN = 16V for t = 10ms. Note 12. Specification for packaged product only.
MIC3975
4
February 2003
MIC3975
Micrel
Typical Characteristics
Power Supply Rejection Ratio
80 VIN = 5V VOUT = 3.3V
PSRR (dB)
Power Supply Rejection Ratio
80 VIN = 5V VOUT = 3.3V
PSRR (dB)
Power Supply Rejection Ratio
80 VIN = 3.3V VOUT = 2.5V
60 PSRR (dB)
60
60
40 IOUT = 750mA COUT = 10F CIN = 0
40 IOUT = 750mA COUT = 47F CIN = 0
40 IOUT = 750mA COUT = 10F CIN = 0
20
20
20
0 1E+1 1E+2 1E+3 1E+4 1E+5 1E+6 1k 10k 100k 1M 10 100 FREQUENCY (Hz)
0 1E+1 1E+2 1E+3 1E+4 1E+5 1E+6 1k 10k 100k 1M 10 100 FREQUENCY (Hz)
0 1E+1 1E+2 1E+3 1E+4 1E+5 1E+6 1k 10k 100k 1M 10 100 FREQUENCY (Hz)
Power Supply Rejection Ratio
80
DROPOUT VOLTAGE (V)
Dropout Voltage vs. Output Current
350 2.5V 1.8V 3.3V
DROPOUT VOLTAGE (V)
Dropout Voltage vs. Temperature
400 2.5V 350 1.8V
VIN = 3.3V VOUT = 2.5V
300 250 200 150 100 50 0 0
60 PSRR (dB)
40 IOUT = 750mA COUT = 47F CIN = 0
300
20
250 3.3V ILOAD = 750mA 200 -40 -20 0 20 40 60 80 100120140 TEMPERATURE (C)
0 1E+1 1E+2 1E+3 1E+4 1E+5 1E+6 1k 10k 100k 1M 10 100 FREQUENCY (Hz)
TA = 25C 250 500 750 OUTPUT CURRENT (mA)
2.8
Dropout Characteristics (2.5V)
OUTPUT VOLTAGE (V) ILOAD =100mA
3.6 3.4 3.2 3.0
Dropout Characteristics (3.3V)
ILOAD =100mA
GROUND CURRENT (mA) 10 9 8 7 6 5 4 3 2 1 0 0
Ground Current vs. Output Current
OUTPUT VOLTAGE (V)
2.6 2.4 2.2 2.0 1.8 1.6 1.4 2
1.8V 2.5V 3.3V
ILOAD =750mA
ILOAD =750mA 2.8 2.6 2.4 2.8 3.2 3.6 4.0 SUPPLY VOLTAGE (V) 4.4
2.3 2.6 2.9 3.2 SUPPLY VOLTAGE (V)
3.5
250 500 750 OUTPUT CURRENT (mA)
Ground Current vs. Supply Voltage (2.5V)
GROUND CURRENT (mA)
GROUND CURRENT (mA)
2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 2 4 6 SUPPLY VOLTAGE (V) 8 ILOAD =10mA ILOAD =100mA
Ground Current vs. Supply Voltage (2.5V)
30
GROUND CURRENT (mA)
1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0
Ground Current vs. Supply Voltage (3.3V)
25 20 15 10 5 0 0 ILOAD = 750mA 2 4 SUPPLY VOLTAGE (V) 6
ILOAD =100mA
ILOAD =10mA
2 4 6 SUPPLY VOLTAGE (V)
8
February 2003
5
MIC3975
MIC3975
Micrel
Ground Current vs. Supply Voltage (3.3V)
30
GROUND CURRENT (mA)
GROUND CURRENT (mA)
1.0
ILOAD =750mA
Ground Current vs. Temperature
GROUND CURRENT (mA)
5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5
Ground Current vs. Temperature
2.5V 3.3V
25 20 15 10 5 0 0 1 2 3 4 5 SUPPLY VOLTAGE (V) 6
0.8 0.6 3.3V 0.4 0.2
ILOAD =10mA
1.8V
2.5V
1.8V
ILOAD = 500mA
0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C)
0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C)
OUTPUT VOLTAGE (V)
8 8 7 7 6 6
2.5V
SHORT CIRCUIT CURRENT (A)
9 GROUND CURRENT (mA)
Ground Current vs. Temperature
3.40
Output Voltage vs. Temperature
2.5 2.0 1.5
Short Circuit vs. Temperature
3.3V
3.35
Typical 3.3V Device
1.8V 3.3V
3.30
2.5V 1.0 0.5
1.8V
3.25
5 -40 -20 0 20 40 60 80 100120140 TEMPERATURE (C)
ILOAD = 750mA
3.20 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C)
0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C)
Error Flag Pull-Up Resistor
6
ENABLE CURRENT A)
12 10 8 6 4 2
Enable Current vs. Temperature
FLAG VOLTAGE (mV) VIN = VOUT + 1V VEN = 2.4V
250 200 150 100 50
Flag-Low Voltage vs. Temperature
FLAG-LOW VOLTAGE
VIN = 5V
FLAG VOLTAGE (V)
5 4 3 2 1 FLAG LOW (FAULT) 1 10 100 100010000 RESISTANCE (k) FLAG HIGH (OK)
VIN = 2.25V RPULL-UP = 22k
0 0.01 0.1
0 -40 -20 0 20 40 60 80 100120140 TEMPERATURE (C)
0 -40 -20 0 20 40 60 80 100120140 TEMPERATURE (C)
MIC3975
6
February 2003
MIC3975
Micrel
Functional Characteristics
Load Transient Response
OUTPUT VOLTAGE (200mV/div.) OUTPUT VOLTAGE (200mV/div.)
Load Transient Response
VIN = 3.3V VOUT = 2.5V COUT = 10F Ceramic
VIN = 3.3V VOUT = 2.5V COUT = 10F Ceramic 750mA
LOAD CURRENT (500mA/div.)
100mA
LOAD CURRENT (500mA/div.)
750mA
10mA
TIME (200s/div.)
TIME (200s/div.)
Line Transient Response
INPUT VOLTAGE (1V/div.)
5.0V
3.3V
OUTPUT VOLTAGE (50mV/div.)
VOUT = 2.5V COUT = 10F Ceramic ILOAD = 10mA TIME (200s/div.)
February 2003
7
MIC3975
MIC3975
Micrel
Functional Diagrams
IN O.V. ILIMIT 1.180V FLAG 1.240V 18V
OUT
Ref.
EN Thermal Shutdown
GND
MIC3975 Fixed Regulator with Flag and Enable Block Diagram
IN O.V. ILIMIT 1.240V 18V
OUT
Ref.
ADJ EN Thermal Shutdown GND
MIC3975 Adjustable Regulator Block Diagram
MIC3975
8
February 2003
MIC3975
Micrel
Input Capacitor An input capacitor of 1F or greater is recommended when the device is more than 4 inches away from the bulk ac supply capacitance or when the supply is a battery. Small, surface mount, ceramic chip capacitors can be used for bypassing. Larger values will help to improve ripple rejection by bypassing the input to the regulator, further improving the integrity of the output voltage. Error Flag The MIC3975 features an error flag (FLG), which monitors the output voltage and signals an error condition when this voltage drops 5% below its expected value. The error flag is an open-collector output that pulls low under fault conditions and may sink up to 10mA. Low output voltage signifies a number of possible problems, including an overcurrent fault (the device is in current limit) or low input voltage. The flag output is inoperative during overtemperature conditions. A pull-up resistor from FLG to either VIN or VOUT is required for proper operation. For information regarding the minimum and maximum values of pull-up resistance, refer to the graph in the typical characteristics section of the data sheet. Enable Input The MIC3975 features an active-high enable input (EN) that allows on-off control of the regulator. Current drain reduces to "zero" when the device is shutdown, with only microamperes of leakage current. The EN input has TTL/CMOS compatible thresholds for simple logic interfacing. EN may be directly tied to VIN and pulled up to the maximum supply voltage Transient Response and 3.3V to 2.5V or 2.5V to 1.8V or 1.65V Conversion The MIC3975 has excellent transient response to variations in input voltage and load current. The device has been designed to respond quickly to load current variations and input voltage variations. Large output capacitors are not required to obtain this performance. A standard 10F output capacitor, is all that is required. Larger values help to improve performance even further. By virtue of its low-dropout voltage, this device does not saturate into dropout as readily as similar NPN-based designs. When converting from 3.3V to 2.5V or 2.5V to 1.8V or 1.65V, the NPN based regulators are already operating in dropout, with typical dropout requirements of 1.2V or greater. To convert down to 2.5V or 1.8V without operating in dropout, NPN-based regulators require an input voltage of 3.7V at the very least. The MIC3975 regulator will provide excellent performance with an input as low as 3.0V or 2.5V respectively. This gives the PNP based regulators a distinct advantage over older, NPN based linear regulators. Minimum Load Current The MIC3975 regulator is specified between finite loads. If the output current is too small, leakage currents dominate and the output voltage rises. A 10mA minimum load current is necessary for proper regulation.
Applications Information
The MIC3975 is a high-performance low-dropout voltage regulator suitable for moderate to high-current voltage regulator applications. Its 500mV dropout voltage at full load and overtemperature makes it especially valuable in batterypowered systems and as high-efficiency noise filters in postregulator applications. Unlike older NPN-pass transistor designs, where the minimum dropout voltage is limited by the base-to-emitter voltage drop and collector-to-emitter saturation voltage, dropout performance of the PNP output of these devices is limited only by the low VCE saturation voltage. A trade-off for the low dropout voltage is a varying base drive requirement. Micrel's Super eta PNPTM process reduces this drive requirement to only 2% of the load current. The MIC3975 regulator is fully protected from damage due to fault conditions. Linear current limiting is provided. Output current during overload conditions is constant. Thermal shutdown disables the device when the die temperature exceeds the maximum safe operating temperature. Transient protection allows device (and load) survival even when the input voltage spikes above and below nominal. The output structure of these regulators allows voltages in excess of the desired output voltage to be applied without reverse current flow.
VIN MIC3975x.x IN CIN OUT GND COUT VOUT
Figure 1. Capacitor Requirements Output Capacitor The MIC3975 requires an output capacitor for stable operation. As a Cap LDO, the MIC3975 can operate with ceramic output capacitors as long as the amount of capacitance is 10F or greater. For values of output capacitance lower than 10F, the recommended ESR range is 200m to 2. The minimum value of output capacitance recommended for the MIC3975 is 4.7F. For 10F or greater the ESR range recommended is less than 1. Ultra-low ESR ceramic capacitors are recommended for output capacitance of 10F or greater to help improve transient response and noise reduction at high frequency. X7R/X5R dielectric-type ceramic capacitors are recommended because of their temperature performance. X7Rtype capacitors change capacitance by 15% over their operating temperature range and are the most stable type of ceramic capacitors. Z5U and Y5V dielectric capacitors change value by as much as 50% and 60% respectively over their operating temperature ranges. To use a ceramic chip capacitor with Y5V dielectric, the value must be much higher than an X7R ceramic capacitor to ensure the same minimum capacitance over the equivalent operating temperature range.
February 2003
9
MIC3975
MIC3975
Adjustable Regulator Design
MIC3975 OUT R1
ENABLE SHUTDOWN
Micrel
sink thermal resistance) and SA (sink-to-ambient thermal resistance). Using the power MSOP-8 reduces the JC dramatically and allows the user to reduce CA. The total thermal resistance, JA (junction-to-ambient thermal resistance) is the limiting factor in calculating the maximum power dissipation capability of the device. Typically, the power MSOP-8 has a JA of 80C/W, this is significantly lower than the standard MSOP-8 which is typically 160C/W. CA is reduced because pins 5 through 8 can now be soldered directly to a ground plane which significantly reduces the case-to-sink thermal resistance and sink to ambient thermal resistance. Low-dropout linear regulators from Micrel are rated to a maximum junction temperature of 125C. It is important not to exceed this maximum junction temperature during operation of the device. To prevent this maximum junction temperature from being exceeded, the appropriate ground plane heat sink must be used.
VIN
IN
VOUT COUT
EN
ADJ GND
R2
R1 VOUT = 1.240V 1 + R2
Figure 2. Adjustable Regulator with Resistors The MIC3975 allows programming the output voltage anywhere between 1.24V and the 16V maximum operating rating of the family. Two resistors are used. Resistors can be quite large, up to 1M, because of the very high input impedance and low bias current of the sense comparator: The resistor values are calculated by:
V R1 = R2 OUT - 1 1.240
Where VO is the desired output voltage. Figure 2 shows component definition. Applications with widely varying load currents may scale the resistors to draw the minimum load current required for proper operation (see above). Power MSOP-8 Thermal Characteristics One of the secrets of the MIC3975's performance is its power MSO-8 package featuring half the thermal resistance of a standard MSO-8 package. Lower thermal resistance means more output current or higher input voltage for a given package size. Lower thermal resistance is achieved by joining the four ground leads with the die attach paddle to create a singlepiece electrical and thermal conductor. This concept has been used by MOSFET manufacturers for years, proving very reliable and cost effective for the user. Thermal resistance consists of two main elements, JC (junction-to-case thermal resistance) and CA (case-to-ambient thermal resistance). See Figure 3. JC is the resistance from the die to the leads of the package. CA is the resistance from the leads to the ambient air and it includes CS (case-to-
MSOP-8
JA JC CA
AMBIENT
ground plane heat sink area
printed circuit board
Figure 3. Thermal Resistance Figure 4 shows copper area versus power dissipation with each trace corresponding to a different temperature rise above ambient. From these curves, the minimum area of copper necessary for the part to operate safely can be determined. The maximum allowable temperature rise must be calculated to determine operation along which curve.
900
COPPER AREA (mm2)
900
40C 50C 55C 65C 75C 85C
800 700 600 500 400 300 200 100 0 0
100C
800
COPPER AREA (mm2)
TJ = 125C 85C 50C 25C
700 600 500 400 300 200 100 0 0
0.25 0.50 0.75 1.00 1.25 1.50 POWER DISSIPATION (W)
0.25 0.50 0.75 1.00 1.25 1.50 POWER DISSIPATION (W)
Figure 4. Copper Area vs. Power-MSOP Power Dissipation (TJA)
Figure 5. Copper Area vs. Power-MSOP Power Dissipation (TA)
MIC3975
10
February 2003
MIC3975
T = TJ(max) - TA(max) TJ(max) = 125C TA(max) = maximum ambient operating temperature For example, the maximum ambient temperature is 50C, the T is determined as follows: T = 125C - 50C T = 75C Using Figure 4, the minimum amount of required copper can be determined based on the required power dissipation. Power dissipation in a linear regulator is calculated as follows: PD = (VIN - VOUT) IOUT + VIN x IGND If we use a 2.5V output device and a 3.3V input at an output current of 750mA, then our power dissipation is as follows: PD = (3.3V - 2.5V) x 750mA + 3.3V x 7.5mA PD = 600mW + 25mW PD = 625mW From Figure 4, the minimum amount of copper required to operate this application at a T of 75C is 160mm2.
Quick Method
Micrel
Determine the power dissipation requirements for the design along with the maximum ambient temperature at which the device will be operated. Refer to Figure 5, which shows safe operating curves for three different ambient temperatures: 25C, 50C and 85C. From these curves, the minimum amount of copper can be determined by knowing the maximum power dissipation required. If the maximum ambient temperature is 50C and the power dissipation is as above, 625mW, the curve in Figure 5 shows that the required area of copper is 160mm2. The JA of this package is ideally 80C/W, but it will vary depending upon the availability of copper ground plane to which it is attached.
February 2003
11
MIC3975
MIC3975
Micrel
Package Information
0.122 (3.10) 0.112 (2.84)
0.199 (5.05) 0.187 (4.74)
DIMENSIONS: INCH (MM)
0.120 (3.05) 0.116 (2.95) 0.036 (0.90) 0.032 (0.81) 0.043 (1.09) 0.038 (0.97) 0.012 (0.30) R
0.007 (0.18) 0.005 (0.13)
0.012 (0.3) 0.0256 (0.65) TYP
0.008 (0.20) 0.004 (0.10)
5 MAX 0 MIN
0.012 (0.03) R 0.039 (0.99) 0.035 (0.89) 0.021 (0.53)
8-Lead MSOP (MM)
MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131
TEL
USA
+ 1 (408) 944-0800
FAX
+ 1 (408) 944-0970
WEB
http://www.micrel.com
The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2003 Micrel, Incorporated.
MIC3975
12
February 2003

▲Up To Search▲

Price & Availability of MIC3975-1

	To Download MIC3975-1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .